NoNecks Garage

NoNecks Garage Welcome to my garage. I can provide low cost auto mods and detailing etc.Lift kits,lowering kits etc. Welding repairs, rust repairs, etc.

I am looking to finally start making some extra cash in the garage. The kids will be back to school and I should have some free time. I can provide low cost auto modifications and aftermarket additions including lift kits, lowering kits car audio upgrades and aftermarket exhaust installations. I love to customize stuff, from guitars to golf carts and everything in between. I can make everything better!

Ok now that that is sorted out back to mounting the fenders back up and fitting the fiberglass hood.
12/22/2025

Ok now that that is sorted out back to mounting the fenders back up and fitting the fiberglass hood.

This cold is for the birds! Installed a new diesel heater for the back of the work truck. Now hopefully I can keep my sp...
12/14/2025

This cold is for the birds! Installed a new diesel heater for the back of the work truck. Now hopefully I can keep my spackle and other supplies from freezing.

Had to keep the lower body line straight so I had no choice but to rework the top of the quarter panel and lower it to m...
12/14/2025

Had to keep the lower body line straight so I had no choice but to rework the top of the quarter panel and lower it to match the door. Not quite done yet but the scary part is over.

Bob Frattone dropped off the oil pan so I could weld in the windage plate and took the carburetor to go through it.
11/27/2025

Bob Frattone dropped off the oil pan so I could weld in the windage plate and took the carburetor to go through it.

The hood hinges that came with my stinger hood were aftermarket and were hindering hood alignment so I cleaned up my ori...
11/27/2025

The hood hinges that came with my stinger hood were aftermarket and were hindering hood alignment so I cleaned up my original ones, and the hood latch in the blast cabinet.

Been making some slow progress fitting panels.
11/27/2025

Been making some slow progress fitting panels.

7 year old batteries in the golf cart finally gave up this year so I upgraded to lithium with 10 year warranty. The 4 le...
06/06/2025

7 year old batteries in the golf cart finally gave up this year so I upgraded to lithium with 10 year warranty. The 4 lead batteries weighed in at about 450lbs. Lithium were 90 total.

Sheet metal Sunday! Got the front fenders and hood hung and about 90 percent fitted. Perfect weather to be inside doing ...
05/05/2025

Sheet metal Sunday! Got the front fenders and hood hung and about 90 percent fitted. Perfect weather to be inside doing this.

Well the time has come to break the seal on these original GM fenders from I guess 1998, more likely from 2002 according...
04/06/2025

Well the time has come to break the seal on these original GM fenders from I guess 1998, more likely from 2002 according to the shipping label to Stockburger Chevrolet.

Had my first visit with the almost complete big block a few weeks ago to check head bolt clearance with headers.Once mot...
04/05/2025

Had my first visit with the almost complete big block a few weeks ago to check head bolt clearance with headers.
Once motor is done, gonna bolt into the frame and order the Tremec TKX 5 speed trans and get driveline completed.

Need more crappy weekends like this so I'm motivated to work on the Chevelle. Did a little gap work on the trunk. Next w...
04/05/2025

Need more crappy weekends like this so I'm motivated to work on the Chevelle. Did a little gap work on the trunk. Next will be assembly of the front end and gapping everything. Then the body will come back off the frame and go back on the rotisserie for weld cleanups underneath then strip roof and doors, sand down all the epoxy primer, re epoxy, bodywork then prime and start block sanding.

Well that was fun...spend half the day getting Dan's new bars installed on his Indian Challenger only to get the dash li...
09/04/2024

Well that was fun...spend half the day getting Dan's new bars installed on his Indian Challenger only to get the dash light up like a Christmas tree and no start! After some troubleshooting, I suspected an issue with the "pre installed wiring" designed to save time. Turns out they installed wiring for wrong year bike. I then had to remove that wiring, remove the original wiring from the original bars, and install that into the new bars and then essentially do the whole job over again.

Address

Southampton, PA
18974

Website

Alerts

Be the first to know and let us send you an email when NoNecks Garage posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category