What are the opening hours?

Monday 8:30am - 5:30pm Tuesday 8:30am - 5:30pm Wednesday 8:30am - 5:30pm Thursday 8:30am - 5:30pm Friday 8:30am - 5:30pm Saturday 8:30am - 5:30pm

Early Pony Parts / FG Autos

Home
Australia
Bendigo, VIC
Early Pony Parts / FG Autos

Specialises in Used 1965 to 1973 Ford Mustang parts, USA Project Cars, RHD Conversions, Mechanical Repairs and 1928 to 1999 Ford Parts

Early Pony Parts and FG Autos specialise in 1965 to 1973 Ford Mustang parts, USA Project Cars, RHD Conversions, Mechanical Repairs and 1928 to 1999 Ford Parts

18/06/2026

Not a lot to report on Box,s Unibody.. Waiting on a few bits, Trans Lines Fittings, Lower Radiator Hose, Inlet Manifold Vacumn Tree, Fan Belt, Battery/Starter Leads.. I was going to put a Mustang Engine Pipe on it to start it as its booked in for early July for Exhaust, but it hits the Old Rear Crossmember.. Lokar Shifter Works.. Just gotta wait till i get it off the Hoist to patch the hole in the Floor where the ol T5 shifter came thru.. I cant get my Guts between the Door and B Pillar while its on the Hoist.. :)

14/06/2026

Sorry Chris... :)

02/06/2026

Got the Lil 289W in Box,s Unibody today.. A Mate came over last week and we set the Pinion Angle up and it was either put packers between the Gearbox and Mount or alter the Gearbox Crossmember, i did the latter.. He measured up for the New Tailshaft while he was here as the C4 is shorter than the T5.. Sent the Radiator off for a flush and it looks like the Aluminum Radiator has a hole in the core, so poor ol box will have to dig deep... :(

21/05/2026

Still setting things up on Box,s Unibody.. Ended up using the 65 Mustang Fan Spacer as the 6 Cyl one was too short.. Mounted the Lokar Shifter to the C4 and the Trans oil and Modulator lines turned up.. I will have to cut off the ol Three Speed linkages off the base of the Steering Column as i rekon there gunna be right where the Exhaust manifold or Engine Pipe will run.. Engine Angle is looking pretty close but i will double check before i start drilling holes for the New Crossmember Mounts..

19/05/2026

Sat a Dummy Windsor Block and C4 Auto in Box,s Unibody, its pretty close to where the Six Cylinder was sitting as the ol Clutch Z bar lines up with the V8 Block.. It cant go any further forward with modifying the Crossmember mounts as they hit the Brake Hose Boss going through the Chassis Rail, i wont do much more with them till i put a degree level on it, underneath the trans looks like its hanging down too much, but the Engine looks okay.. I will sit a Timing casr Cover and Water Pump on the Engine to check for Radiator clearance, but im thinkin theres going to be plenty, we are two Cylinders shorter this time

12/05/2026

I had a busy day today... The owner of the Blue mustang picked his Car up.. I got my Hands greasy on the Uniboys Engine and Trans removal... You rekon the Owner could have hot washed the Engine Bay for me before delivering the car... The 5 Speed ended up being a normal T5 and not a S10 5 speed like i thought it was.. Ideal for Bench Seat Cars the S10,s are.. De grease time next and back on the Hoist to start the V8 conversion..

08/05/2026

The Blue 65 Coupe is done, well my part of it, the owner is picking it up early next week.. Another job turned up this week.. The Ol Ford Unibody Pick Up is getting a Heart Transplant for the rather large owner!! (Yes i know, Pot callin the Kettle Black!) Its having a 289 Windsor and C4 fitted.. :)

05/05/2026

Happy to report i havent had any Forklift mishaps the last few Days! The Owner of the Burgundy 65 Couple has organised a Sparky to do the Custom Wiring on his Car.. Sat the EFI Tank in its hole in the Boot ( Trunk) Custom Dash Bezel and Guages.. This thing is going to be Fast! Driver Training booking needed.. :)

01/05/2026

Well today was one of those days! All my own fault.. Ive been meaning to get fixed the Tilt Ram on the Forklift as it been leaking for years, but recently sq**rting from the seal, hence it cant hold pressure.. So stupid me let the 33 Sedan/Coupe have a sleep!! Well its got a good Chassis ( Frame)!!!.. Just missed the Falcons sitting behind it.. Put a scratch in the 65 Mustangs Rear Quarter extension as thats what i was lifting the Sedan and Mayrack in one and a slight incline and then the Forks tilting forward and down it went.. Im not game to take the Tarp off yet, but i know the left B pillar has been bent in at the Roof! Is it Beeroclock yet?

24/04/2026

Yes i know im supposed to be Welding, but these nice Sunny Days draw you outside.. So i pulled the Plugs on the Ol 33 Sedan/Coupe Project to sq**rt some l**e into her as she is stuck.. Pretty Original ol 33 Motor by the look of it.. Still has the Detriot lubricator Carby and Correct Inlet Manifold.. I rekon i will keep her as a Six Wheel Equipped Car too..

Address

235 East Lloyd Street
Bendigo, VIC
3550

Opening Hours

Monday	8:30am - 5:30pm
Tuesday	8:30am - 5:30pm
Wednesday	8:30am - 5:30pm
Thursday	8:30am - 5:30pm
Friday	8:30am - 5:30pm
Saturday	8:30am - 5:30pm

Telephone

+61354431841

Website

http://earlyponyparts.com.au/

Alerts

Be the first to know and let us send you an email when Early Pony Parts / FG Autos posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Early Pony Parts / FG Autos:

Shortcuts

Address
Telephone
Opening Hours
Alerts
Contact The Business
Claim ownership or report listing

Want your business to be the top-listed Autos & Automotive Service in Bendigo?