Doug's Garage/FoxWerks

Doug's Garage/FoxWerks I specialize in Foxbody Mustangs. Can complete repairs, upgrades, tune-ups, fender rolling, 5 lug swaps, install power adders, build fuel systems. Just ask

Adam getting work started!!
03/22/2026

Adam getting work started!!

I sent Matt's turbo kit out to get coated! Sure looks good all cleaned up. Will be dark gray when coated!
02/16/2026

I sent Matt's turbo kit out to get coated! Sure looks good all cleaned up. Will be dark gray when coated!

Hmm.. I think it's time for a new FoxWerks T shirt! Thanks Justin Cromeens
01/01/2026

Hmm.. I think it's time for a new FoxWerks T shirt! Thanks Justin Cromeens

01/01/2026

Happy New Year! The 91 Calypso Coupe goes home to its new owner today!

Getting another one Sorted out. 91 Calypso Coupe!. Cleaned up wiring and a nice tuck. Added a MicroSquirt. Working on t...
12/25/2025

Getting another one Sorted out. 91 Calypso Coupe!. Cleaned up wiring and a nice tuck. Added a MicroSquirt. Working on the tune next and some minor cosmetic stuff.

11/30/2025

The 89GT is almost Done! NEW: SVE 170 heads, B cam, Edelbrock Perforner RPM intake, 30lb injectors, Contour fans, BBK longtubes, BBK catted x pipe, MicroSquirt, Eibach Pro Kit springs, inner and outer tie rods, lower A arms ball joints, Aluminum drive shaft, LED cluster lights! Just one last part to install, the Aeromotive 340 fuel pump. Has a nice chop with the B cam even thru the cats.. lol. Owner loves it!!

Here is a Nice GT project I took in for a relatively quick turn around. New Heads, Cam, intake, longtubes, injectors, s...
11/15/2025

Here is a Nice GT project I took in for a relatively quick turn around. New Heads, Cam, intake, longtubes, injectors, some killer powder coating. Adding a MicroSquirt, subframes, lowering springs, aluminum drive shaft. A foxlocks.. its 37k mile car.. its Clean!

11/15/2025

Quick house call this morning for the dreaded BBK fuel pressure regulator/rail fuel leak. Got it all squared away! Joey Hafner your GT needs a bath! Lol

Finally happy with how the sheet metal work looks in the engine bay. Need to fit/address the two Gates and the charge p...
09/01/2025

Finally happy with how the sheet metal work looks in the engine bay. Need to fit/address the two Gates and the charge pipe from BOV to TB. Then, the kit can be cleaned and and coated.. pull motor and paint this sucker! Lol

Decided to just weld up/repair the factory fender aprons as no cover style panel was going to work well with the turbo k...
07/15/2025

Decided to just weld up/repair the factory fender aprons as no cover style panel was going to work well with the turbo kit.. next will be the passenger side.. Will be a much bigger pain! Lol. Then some more touch up shaping and body/panel working.

06/28/2025

Another quick tune and minor wiring fixes for a past FoxWerks customer, Floyd Coleman .. just installed a new Power Master 200amp one wire alternator and wrote a complete new tune for this 363 Turbo combo vs the 306 S trim combo it had 3 years ago.

After about a year and a half.. i did some more tuning on Shelby Dane Sowell 's 88 Coupe. There were issues the last tim...
06/08/2025

After about a year and a half.. i did some more tuning on Shelby Dane Sowell 's 88 Coupe. There were issues the last time. I added a TurboSmart E2 boost controller, set the fuel pressure correctly, added a boost and AFR display to his DD-EFI dash and made several suggestions on what he needs to correct with the manual brakes and wiring.. plus rolled the rear fenders! Car hauls ass! Lol

Address

Carrollton, TX
75007

Website

Alerts

Be the first to know and let us send you an email when Doug's Garage/FoxWerks posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category