SCP, Speed Custom & Performance Inc.

09/04/2026

SCP will be closed this Saturday 9/5/26. We will reopen Tuesday. Happy Labor Day!!

08/27/2026

***** RACE GAS *****

37 gal of Renegade Pro Super Late Model $500

SOLD ** 54 gal (full drum) of VP Late Model Plus $725 ** SOLD

Jaz & Scribner fuel jugs $15/each or $40 for 3
CLEAN Renegade or VP empty drums $10 each
Cash Only ** Pick Up in High Ridge, Missouri 63049 ** 20 minuets from I-55 Race Track

09/02/2025

NEW SBC DART SHP Block & NEW Rotating Assembly
Big Bore Short Stroke 385” Motor
New Dart SHP Block 4.155” Bore, 350 Mains
Block Has Been Fully Race Prepped:
Square Decked W/BHJ Fixture
Finished Honed W/Deck Plates
Lifter Bores Honed To Spec
Solvent & Water Washed
HP Cam Bearings Installed
Stainless Steel Freeze Plugs Installed
Pipe Plugs & Dowels Installed

New Lunati 46 lb 3 9/16” Stroke Crankshaft
New Callies/Compstar H-Beam 6” Rods
New Ross Forged Pistons w/11cc Domes
Seal Power Premium Rings
ACL Race Series Main Bearings
ACL Race Series Rod Bearings
Precision internally balanced w/heavy metal
Ready to assemble and WIN!!
$5900 cash.
Pick up at Speed Custom & Performance in High Ridge, Missouri

08/11/2025

Would like to thank all of you who volunteered to clean our bathroom UNTIL you found out we used windshield washer fluid for the “Frosty Down the Sh***er” picture. Damn it!!

08/10/2025

VP “Stay Frosty” Down The Sh***er!
Decided to change motors in our modified last week. Realizing we had $35/gal Frosty in the motor it became a challenge to recover every drop. We carefully removed the pipe plugs to drain the block. BAD NEWS, ¾ of a gallon ($26) down the “sh*tter”! It was all over the floor resulting in a big mess to clean up. It was impossible to get plastic container under the drain holes. The solution!! Called my buddy at the surplus store who found a hex fitting that will screw into the block and gets your drain point away from the block and over the pan rails. The fitting is steel, sticks out less than an inch and allows precision draining into a container. Figuring everyone has the same problem, we decided to put a kit together with 4 fittings and sell it for $12.00. If you buy it with VP Frosty you will get a 20% discount on the kit. ( If you have already bought Frosty from us the 20% will apply.) On our UMP motors with an aluminum Olson pan we use an additional 45 degree fitting that sells for $6.00.

08/10/2025

07/25/2025

Time To Get Tanked & Releave Those Butt Aches!
Every racer knows he should change the fluid in his Bert or Falcon transmission every 3- 4 nights. It is cheap insurance. It is not hard to drain but it is a pain in the ASS to refill. Lay on your back with a wrench, funnel, hose, pump, measuring cup, flashlight and a roll of paper towels to clean up the mess. The solution!! We had a small DECK mounted aluminum tank built that allows you to fill the transmission standing up on the outside of your car. Pour your fluid in a measuring cup, unscrew the cap and dump it in. (NOTE: Be sure & have “the wife” get down there & put the drain plug back in!!)

07/22/2025

Water Temp Guage Causing Stains in Your Underwear?
VP Racing new product Stay Frosty Coolant may be your solution! It is NOT an additive, instead it REPLACES your current coolant. Stay Frosty is designed for high heat racing engines. VP claims up to a 30 degree reduction in temperature. Our SCP A-Mod was running 230-240 degrees after a feature. We built a shroud, changed fans and even removed the screen in front of the radiator. Still the same temps after a race. In desperation, we bought 3 gallons of the Racing Stay Frosty. Drained the old coolant, filled it up with Stay Frosty and off to the races on another heat wave July night. Results were pretty amazing, first night we ran 200 degrees and the following week on a heavy, heavy track we ran 210 degrees. “Praise the Lord” no more STAINS!!

07/03/2025

SCP will be closed Friday July 4th & Saturday July 5th. We hope everyone has a fun, safe holiday weekend!

12/12/2024

BODY PANEL OPTIONS!!

SCP is now stocking plastic MD3 body panels along with continuing to keep a full line of Stakt panels.

Come by and check out both! Save some time and leave your hammers in the toolbox for 2025!!