Miller's Custom Garage LLC

Miller's Custom Garage LLC fixing a little bit of everything!!! just ask I'll see what I can do!! all your repair needs on abou I do work weekends if it's an emergency!!

New Holland Boomer 40 4wd tractor!! Clutch kit and PTO dampener installed good fun!! Thx for looking and keep on wrenchi...
06/05/2026

New Holland Boomer 40 4wd tractor!! Clutch kit and PTO dampener installed good fun!! Thx for looking and keep on wrenching!!

2002 Windstar customer started engine slight knock noise and oil leak... Still running with the hole in the oil pan lol ...
05/25/2026

2002 Windstar customer started engine slight knock noise and oil leak... Still running with the hole in the oil pan lol performed an engine swap with a good used one ready for another 200k miles!! Thx for looking and keep on wrenching!!!

2020 Durango 8 speed transmission after warmed up vehicle had no reverse. Found valve body bypassing fluid. Installed a ...
05/13/2026

2020 Durango 8 speed transmission after warmed up vehicle had no reverse. Found valve body bypassing fluid. Installed a valve body rebuild kit!! Hopefully more parts come available for these very soon!! The struggle is real lol
Thx for looking!!
Keep on wrenching!!

2022 Genesis G70 3.3L Turbo Spark plug threads came out when the customer went to change plugs.Luckily I was able to use...
04/30/2026

2022 Genesis G70 3.3L Turbo
Spark plug threads came out when the customer went to change plugs.
Luckily I was able to use a Ford Triton insert and the tool to repair the threads!!! Happy it went well!! Lol thx for looking and keep on wrenching!!!

2015 Chevy Spark CVT transmission replacement!!! I'm thinking the smaller the car the more that has to come apart lol Th...
04/26/2026

2015 Chevy Spark
CVT transmission replacement!!! I'm thinking the smaller the car the more that has to come apart lol
Thx for looking and keep on wrenching!!

2010 Charger 3.5L Customer compliant of a vibration while at idle. There weren't any misfires showing up on the ECM dat...
04/17/2026

2010 Charger 3.5L
Customer compliant of a vibration while at idle. There weren't any misfires showing up on the ECM data stream. So back to basics with a compression gauge and a cylinder leak down tester!!! Compression test didn't show much but the leak down test sure did!!! Found exhaust valve leaking and several other cylinders very high in leak down test!! All new valves, timing kit and gasket kit!! It's ready to roll without vibrations!!! Thx for looking and keep on wrenching!!

2014 F250 6.7L 4wd Cam sensor replacement!!! ummm sometimes it's just easier to dig into a job !!! Then trying to sho...
04/17/2026

2014 F250 6.7L 4wd
Cam sensor replacement!!! ummm sometimes it's just easier to dig into a job !!! Then trying to short cut the task!! In saying that. The you tube video short cuts sucked for this task LMAO but at least it's a completed task and the DTC isn't returning!!
Thx for looking keep on wrenching!!

2019 Colorado rear diff bearing failure on the inner pinion shaft!! Installed a new bearing, shims and seal kit and clea...
04/07/2026

2019 Colorado rear diff bearing failure on the inner pinion shaft!! Installed a new bearing, shims and seal kit and cleaned debris!! Running down the road again, quietly I might add lol thx for looking and keep on wrenching!!!

Anyone needing Lawnmowers serviced?? Get them ready for the summer!! Oil change...Grease components... Install Spark plu...
03/30/2026

Anyone needing Lawnmowers serviced?? Get them ready for the summer!!
Oil change...Grease components... Install Spark plugs.. fuel filter... Air filter.... And Sharpen blades... With a general inspection and a battery charge up and test!!!
Lawn tractors and zero turns price runs about 200$ or less on most applications!! One week turn around time at the moment!!! "Ordering of parts and maintenance items week in advance"or "the same week on some applications!!"
Anything found during inspection would be noted and estimate given to customer! As this would be extra charge from the service. Such as "Belts, pulleys, blades, battery, tires, etc".
50$ pick up and delivery fee in surrounding area!!!
Thx for looking and keep on
wrenching!!!
Call or text (812) 229-0933
Or message the FB MCG shop page!!! Or even my personal messenger!!

Address

934 South Morgan Street
Brazil, IN
47834

Opening Hours

Monday 9am - 6pm
Tuesday 9am - 6pm
Wednesday 9am - 6pm
Thursday 9am - 6pm
Friday 9am - 6pm

Telephone

(812) 229-0933

Website

Alerts

Be the first to know and let us send you an email when Miller's Custom Garage LLC posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Miller's Custom Garage LLC:

Shortcuts

Share